Skip to content
Ring (562) 647-6550

Guide ยท Whittier

PEX repipe cost

National guides price a whole-house PEX repipe at roughly $4,000 to $10,000, about a third less than copper. This page lays out the numbers by size, material and extras so a bid is easy to read.

Last changed

Floating columns showing PEX and copper repipe price ranges for one, two, three and four-plus bathrooms.

Published guides price a PEX whole-house repipe starting near $4,000 and topping out near $10,000, with copper starting around $6,000 and passing $15,000. Bathrooms, house size, wall access and finish repair decide where a particular house lands. For what the job involves, see repiping and pipe replacement; the rest of this page turns the money into pieces.

What do homeowners usually pay for PEX?

The Plumbing Price Guide puts installed PEX at $3-$7 per linear foot, which totals $4,000-$10,000 for a whole house. Bob Vila quotes a $7,500 average across every pipe type, a $1,500-$15,000 spread, and $0.40-$2 per foot for PEX tubing alone before labor. Plan on the $4,000-$10,000 band.

Compare tubing-only with installed prices and you see where the money goes: labor. Labor is the largest piece, and a bigger house or tougher access pushes it up. All of it is national data, so a bid on your own house is the price that counts.

How do bathrooms and square footage change the price?

One guide sorts repipe pricing by bathroom count and floor area. A compact one-bath house lands at the low end of PEX pricing, while a large home with four or more baths reaches toward $14,000. The tiers are laid out below for both pipe materials.

  • Compact house, one bath, below 1,200 sq ft: PEX $2,500-$5,000, copper $4,500-$8,000.
  • Two baths, roughly 1,200-1,800 sq ft: PEX $4,000-$7,500, copper $6,000-$11,000.
  • Three baths, roughly 1,800-2,500 sq ft: PEX $6,000-$10,000, copper $8,000-$15,000.
  • Four baths or more, above 2,500 sq ft: PEX $8,000-$14,000, copper $12,000-$20,000 and up.

So a two-bathroom house lands in the middle of the PEX range, and each added bath adds a couple of thousand dollars. Bob Vila prints a lower number, $2,280-$5,120, for a house with three bedrooms and about 1,500 sq ft, which shows quotes can come in under these tiers. Read both as boundaries, not promises.

What does copper cost compared with PEX?

In the Plumbing Price Guide, a copper whole-house repipe starts at $6,000 and passes $15,000, which is $6-$14 per installed foot against $3-$7 for PEX, and the guide credits PEX with 30-40 percent savings. For tubing only, Bob Vila lists copper at $2-$8 per foot and PEX at $0.40-$2.

Copper costs more because the tubing is pricier and it goes in rigidly, joint by joint, soldered or press-fit, with more fittings. Plenty of owners still prefer it for its long record. To weigh other differences, see PEX versus copper, and make sure a copper bid states the joining method.

CPVC, a rigid plastic, lands in between according to that guide: $4,500-$11,000 for a whole house, or $3-$8 per foot installed.

What about flow rate, PEX versus copper?

Capacity follows inside diameter, fittings and pressure, not the material name. PEX tube of a given nominal size generally has a somewhat narrower bore than copper of that size, and fittings narrow it further, so installers often size up or use a manifold layout. Ask for the manufacturer's sizing table covering the product that will go in.

No flow chart appears here, because the numbers vary by brand and fitting style and we would rather send you to the maker's data than invent one. A properly sized PEX system normally delivers the flow a house needs. Ask the installer how the main and long runs were sized and whether a regulator is included; the state code (608.2) puts the cap on building supply pressure at 80 psi.

What does replacing polybutylene cost?

Neither guide prints a separate polybutylene figure. It gets replaced as part of an ordinary whole-house repipe, often with PEX, so use the same ranges. The Plumbing Price Guide adds that some insurers may refuse coverage on polybutylene and recommends a full repipe over a partial one.

The material, a gray or bluish plastic, shapes the plan more than the price. If you have it, the scope is normally every supply line, and bathrooms and access still drive the cost. Spotting it is covered in polybutylene pipe replacement, and the other common old material is handled in galvanized pipe replacement.

Do mobile homes cost less?

Published guides vary on repiping a mobile home, which usually has less pipe and often simpler runs than a house. Supply lines often run under the floor, where they can be damaged, which changes the work compared with a house. No further breakdown is printed, so ask for a bid.

Related questions are answered in installing plumbing under a mobile home and in the guide to inspecting mobile home plumbing.

What else gets added to the bill?

Several items often sit outside the repipe price: drywall repair and paint at $1,000-$3,000, permits at $100-$400 depending on the city, each extra fixture hookup at $200-$500, and drain or sewer replacement at $2,000-$8,000 or more when that is needed as well. Ask which are included, and which you are expected to arrange.

Five stacked boxes: the repipe itself, drywall and paint, permits, each extra fixture, and drain work.

Slab homes cost most, since lines have to be rerouted through walls or the attic. The guide does not give a dollar figure for that case. Drywall repair done separately can sometimes save money, scheduling in spring or fall can help and combining a repipe with a remodel or water heater replacement avoids opening walls twice. Ways to trim the total are described in what repiping a house costs.

How should I compare repipe quotes?

Line them up by material, number of fixtures reconnected, drywall and paint, permit, pressure regulator, warranty and time on site. A low bid that excludes wall repair is not cheaper than a higher one that includes it. Ask each contractor to price the same scope, and confirm the contractor license with the CSLB.

For Whittier addresses permits come from the city's Building and Safety office, and each neighboring city keeps its own. For a price, send the price request form listing the bathroom count, the house size, the pipes' material if known and any leak history. Someone local is arranged to quote it.

Common questions

What is the schedule for a PEX job?

Per the Plumbing Price Guide, a standard house needs two to five days, a compact home with open access about two, and a large one with pipe in finished walls up to a week, with drywall repair on top. The supply is off during parts of each working day.

Which questions help me pick a PEX contractor?

Which PEX type and fittings they use, how they size the lines, what the price includes for drywall, permit and a pressure regulator, how many days they expect to need and what warranties come from the manufacturer and the contractor. Look up the license via the CSLB and have the figure written down.

Does someone need to stay during the job?

An adult should be available when the crew arrives and again when they leave, to give access, approve changes and review the work. Expect dry taps through part of the day, open closets, free the space around the water heater and empty under-sink cabinets, and keep animals clear.

Will PEX always beat copper on price?

Usually, by about 30-40 percent in the guide we read, though not always. A complicated house or poor access can narrow the gap, and labor is a larger share of the total than the pipe. Get PEX and copper quotes for the same scope and compare the totals.

References