Drain the line, dry the copper, then wrap a clamp over the hole. That buys hours or days. The permanent answer is to excise the bad stretch and splice fresh pipe into the gap. One pinhole often has siblings, so the sections below also cover what to check next. For the bigger picture on leaks, see the leak and burst pipe service page.
A copper line is misting or spraying right now: what comes first?
Turn off the supply. Next, crack the nearest low faucet to let the pipe drain and the pressure fall. Kill breakers for nearby outlets if anything electrical is damp. A pinhole can announce itself as a fine mist, a hiss or a green crust, so wipe the area and mark the spot with tape before the evidence disappears.
If the valve refuses to turn, slide towels beneath the leak and ring a plumber and leave the valve alone. Stay away from wet outlets, fixtures and ceilings that hang near wiring. Ten minutes of work: bucket under the drip, fan blowing on the wall.
What about a cracked PVC joint or a pipe that split outdoors?
Cut away the failed joint, clean the ends, and glue a fresh coupling in using primer and solvent cement, then let it cure for the period the label gives before turning water on. An outdoor hose line or sprinkler riser follows the same steps, and push-fit couplings suit plastic and copper alike.
Cement will not grip a wet surface, so dryness is the whole game. Match the cement to the plastic type too. Read fixing a leaking pipe joint and the longer treatment of plastic pipe leaks. A leak buried in soil or beneath concrete gets its own discussion in slab leak repair or repipe.
How do I fix it for good?
Make a cut either side of the damage, lift out the section, ream the ends smooth and splice new copper in. Joints can be soldered, pressed or made with push-fit fittings. Smearing solder over a pinhole seldom works, since pipe wall next to the hole is usually as thin as the spot that failed.
Sweat soldering takes a torch, a flux brush, lead-free solder and a bone-dry line. An open flame beside wood framing is the reason plenty of homeowners hire this out. Push-fit fittings avoid fire but cost more each. A short spot repair sits well under California's $1,000 point for contractor licensing, though permit work of any size is covered by it.
What is the drying routine for a ceiling that got wet?
Find and close the source before you do anything else. If drywall bulges with trapped water, stay clear of it and call a professional. Pull out wet insulation, then keep fans and a dehumidifier going until framing and board feel dry. EPA's mold guidance suggests finishing the job within a day or two.
Board that sags, crumbles or smells generally has to go. Board that stays flat and firm may dry, and can be primed with a stain blocker and repainted. A stain that comes back signals continuing moisture. In warm weather mold moves quickly, so visible growth is a reason to pause and plan. Our ceiling leak guide goes further.
How would I know a pipe has failed behind a wall?
Clues include a stain that spreads, blistering paint, boards that run warm, a musty smell, or the sound of flow while every fixture is shut. A wall that stays damp after the supply is closed may be taking water from elsewhere, so follow the stain upward.
Try the meter test. Record the dial, then wait two hours without touching a tap and compare. EPA describes the same method, and the typical home loses more than 9,300 gallons a year to leaks, in EPA's estimate. Movement on the dial means a plumber can pinpoint the break using acoustic equipment or a camera; leak detection cost explains the pricing. For more warning signs, read recognizing a pipe burst.
Which temporary fixes actually hold a pinhole?
Three do: a repair clamp (rubber sleeve inside a steel band) sized for the pipe, self-fusing silicone tape stretched tight over dry copper, and two-part epoxy putty kneaded into the hole. All are stopgaps. Choose the clamp when you can reach around the pipe, and tape or putty for a tiny weep on a clean surface.
Each fix needs a dry pipe, so empty the line first. Reopen the valve in small increments and monitor the patch for a good while. Skip temporary fixes inside a closed wall, where a failure would flood unseen. A hose clamp over a scrap of rubber is the improvised cousin, and proper parts should replace it quickly.
Why does copper develop pinholes?
Corrosion eats pits from the inside. Fast flow, chemistry, leftover flux, heat and decades of service all feed it. Whittier area houses are often postwar, and the Census Bureau's survey gives 1959 as the median build year in Downey and 1957 for both Norwalk and Pico Rivera, so older copper is common.
Take a second pinhole as a warning, not a coincidence. Ask whoever repairs the first one to inspect neighboring lengths for green spots, rough surfaces or pitting. If more than one section is failing, compare serial patches against repiping the house, and see how often to repipe for the usual timing.
Common questions
Is epoxy putty a permanent answer?
No. It holds a small hole for a while but can let go when pressure rises or the pipe flexes. Think of it as a stopgap before a proper splice, and move faster if the surrounding copper looks green, rough or pitted. Do not bury it behind a finished wall.
Does a pinhole repair require a permit?
A one-section spot repair generally does not, whereas replacing large runs may. For your address, ask the City of Whittier Building and Safety Division at (562) 567-9320 or the office in your own city, and have the plumber confirm before work starts.
Is it possible to solder a wet pipe?
No. Water in the line soaks up the heat so the joint never gets hot enough, and steam can blow the solder out. The line has to be completely drained and dry before any torch comes out. Press and push-fit fittings sidestep the problem, which is why many people choose them.
Who comes out for a pinhole in copper?
On the price request form, give the location of the leak, the pipe material and the damage. Once we arrange a local plumber, the written quote itemizes the repair, any wall opening and any drying, so you see the whole bill in advance.
This guide is one of many on plumber whittier.