Skip to content
Ring (562) 647-6550

Guide ยท Whittier

Installation cost of a tankless water heater

Published figures for unit, labor, gas line, venting and permit costs, what pushes a quote up, and how a tankless job compares with replacing a tank.

Last changed

Hub diagram of the six quote lines that make up the installed price of a tankless heater.

Bob Vila's national guide puts an installed tankless heater anywhere from $1,333 up to $3,721, centered on $2,527. The swing comes from the fuel, the distance to the gas meter, and whether venting and gas piping have to be redone. Ordinary tank heaters, and their repairs, are the subject of the water heater repair page.

How much does tankless cost with installation?

Fuel matters here. The guide shows electric units at $800 to $1,500 installed, natural gas and propane at $1,000 to $1,500, and solar at $1,700 to $6,000. Those fuel figures sit under the headline range, which also counts bigger whole-house models and the extras covered below.

On pricier jobs the unit is the smaller piece. A single-point electric model averages about $450, and top-end gas units can pass $1,500. A Whittier house with a gas tank heater will usually look at the gas numbers, since SoCalGas serves the city and the supply already exists, though its capacity deserves a check.

What goes into a quote?

Five lines: the unit, labor, gas or electrical upgrades, venting, and permit plus removal of the old tank. Plumber labor in the guide spans $600 to $1,850 for roughly three hours of work. Electricians add $50 to $100 an hour, usually for up to two hours, on electric conversions, and pipe insulation costs about $10 a foot.

Item Published figure
Gas line work up to $1,000 extra
Tight or awkward location add 10 to 15 percent
Hauling off the old heater from $500
Permit $50 up to $100
Natural gas, yearly running cost around $200

Stack them up: a plain swap lands low in the range, and a relocation with new venting rides high. Have each bidder price those lines apart, so the bids line up.

Why might a gas tankless unit need a bigger gas line?

Heating water on demand means burning gas in a big burst, more than a tank's slow burner draws. The old pipe may have been sized for the slow burner, so part of the run back toward the meter could need upsizing. Bob Vila prices that gas line work at up to $1,000 on top.

Thin gas pipe for a tank's slow draw, thick pipe for a tankless burst.

Venting is the other wild card, because a tankless unit wants its own approved flue and the tank's old one often will not match. Per-foot pricing for pipe is on the gas line costs page. Gas piping counts as permit work in California, so look for a contractor whose state license is current.

What is the labor charge for swapping a heater?

For a standard tank swap, with no relocation or fuel change, Bob Vila lists labor at $150 to $450 per job. A tankless install takes longer and carries the larger labor figure above. Hourly plumber pay in these surveys runs from $45 to $200.

The replacement guide quotes a complete tank-type swap, materials and labor, at $600 to $3,500 electric and $700 to $2,700 gas. Tank size, venting and local code explain the width. For a closer look at tanks, read 50-gallon replacement cost.

Do 40 and 50 gallon tanks differ in price?

The guides we read never split 40 gallon from 50 gallon tanks in price; Bob Vila notes only that 40 gallons is the most common size. Capacity nudges the tank price while labor, venting and permit stay roughly level. The quote should name tank size and brand.

So be wary of any single number for a tank size. A bid that lists size, fuel, warranty, drain and discharge pipe and permit shows the true difference. A part often added to a swap is covered on the expansion tank replacement page.

What do valves, anode rods and parts cost?

In Bob Vila's repair guide a relief valve with a plumber is about $200 to $300, a thermostat roughly $150 to $200, an element around $200 to $300, an igniter $75 up to $350, and an anode rod a $20 to $50 part plus labor. Flushing the tank is near $200. The guide puts a gas control valve at $300 to $500.

Hard water is the reason anode rods and descaling matter in this area: Whittier's 2025 city water report shows hardness near 14.6 grains per gallon. Ask each bidder if a descaling kit and isolation valves come with a tankless unit. The rod itself is explained on the anode rod replacement page.

Book a plumber quote

Fill this in and we'll arrange a local plumber specialist to come and price the job.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who takes your job. You pay us nothing.

Does a tankless heater earn its cost back?

Operating cost is lower for gas units in Bob Vila's data, at about $200 a year for natural gas and $350 for propane, but it does not give an electric figure because rates vary. A tankless unit avoids standby loss from a stored tank, though savings depend on use, and the higher install price can take years to repay.

It depends on household size and how many years the unit lasts. Homes with steady daily use, a tank that is hard to fit, or a space shortage gain the most. Bob Vila gives no lifespan and manufacturers differ, so get warranty terms on paper.

What permits and inspections apply?

A heater swap or move generally needs a permit, and Bob Vila shows $50 to $100 on the tankless job. Whittier's Building & Safety Division, (562) 567-9320, runs permits and inspections, and gas piping, venting changes and electrical upgrades are what the inspector checks.

Settle who handles the permit and whether its fee sits in the quote; the water heater permit page lists the steps. Bigger jobs call for a contractor whose state license is current.

Common questions

How long is the visit?

The guide's working assumption is about three hours of plumber labor for a straightforward swap. A new location, gas line, vent run or electrical circuit stretches that and may need a second day. Inspection scheduling is separate, so request the full timeline on paper.

Which questions go to each bidder?

Get the model and capacity named, then ask if gas line upsizing and venting are inside the price, how long the warranty runs, and whether the descaling kit and isolation valves are supplied. Keep the contractor's license number on file and compare two written quotes, minimum.

Must I be there?

Yes. An adult should meet the visitor, point out the old unit, sign off on any change in scope and join the closing walkthrough. Water and gas stay shut for a good part of the day. Cannot attend? Name your stand-in in the request.

Is a free estimate available?

Plenty of contractors estimate before they commit. Ask whether the visit costs anything, whether that fee comes off the job, and whether the figure is firm or a range. A quote for your address begins with the price request form; nothing becomes final until you say yes.

References